MHI2 full conversion to EU: Difference between revisions

From MIB-Helper.com Wiki
Jump to navigation Jump to search
← Older edit
No edit summary
 
(7 intermediate revisions by the same user not shown)
Line 32: Line 32:


# Insert SD card with More Incredible Bash
# Insert SD card with More Incredible Bash
# <code>REM</code> → <code>Update</code> → SD card → install More Incredible Bash
# <code>REM</code> → <code>Update</code> → <code>SD card</code> → install More Incredible Bash


=== Prepare unit for EU firmware ===
=== Prepare unit for EU firmware ===
# [[GEM]] → m.i.b. → advanced_settings → eu_conversion → convert unit to EU. It will end with "reboot (..) and run conversion again"
# <code>GEM</code> → <code>m.i.b.</code> → <code>advanced_settings</code> → <code>eu_conversion</code> → <code>convert unit to EU</code>. It will end with "reboot (..) and run conversion again"
# reboot the unit, and run the `convert unit to EU` again
# reboot the unit, and run the <code>convert unit to EU</code> again.
# ...and again - you see "Now you can insert (...) and update".
# ...and again - you see "Now you can insert (...) and update".


Line 44: Line 44:
# exit GEM by going to <code>RADIO</code>. Don't reboot the unit.
# exit GEM by going to <code>RADIO</code>. Don't reboot the unit.
# insert FAT32 SD with target firmware
# insert FAT32 SD with target firmware
# REM → Update → User defined → RightButton → Set all to <code>[Y]</code>
# <code>REM</code> → <code>Update</code> → <code>User defined</code> → <code>RightButton</code> → Set all to <code>[Y]</code>
# if you have premium sound system with external audio amplifier (Bose, Dynaudio, Fender, Bang&Olufsen...), set the amplifier (<code>AMP16*APN / AMP_BAO_P3 / Bose6416*</code>) to <code>[N]</code>, because we don't want to update the amplifier. You could do it, but you will need to upload correct parameters to the amplifier afterwards.
# if you have premium sound system with external audio amplifier (Bose, Dynaudio, Fender, Bang&Olufsen...), set the amplifier (<code>AMP16*APN / AMP_BAO_P3 / Bose6416*</code>) to <code>[N]</code>, because we don't want to update the amplifier. You could do it, but you will need to upload correct parameters to the amplifier afterwards.
# if you have Audi A3 8V (<code>AU37x</code>), set the <code>FC2H37xE</code> to <code>[N]</code>.<ref>https://www.drive2.ru/b/651027432949678987/</ref> This is the display mechanism firmware. If you flash it with the EU firmware version, the mechanism will stay permanently open.
# if you have Audi A3 8V (<code>AU37x</code>), set the <code>FC2H37xE</code> to <code>[N]</code>.<ref>https://www.drive2.ru/b/651027432949678987/</ref> This is the display mechanism firmware. If you flash it with the EU firmware version, the mechanism will stay permanently open.


=== Start the EU firmware update ===
=== Start the EU firmware update ===
# scroll down → Start update; wait...
# scroll down → <code>Start update</code>
# In "Device summary" scroll down → Resume
# wait...
# wait for reboot, go to MMI settings and set your language
# In "Device summary" scroll down → <code>Resume</code>
# wait for reboot
# go to MMI settings and set your language


== Patch the unit ==
== Patch the unit ==
Line 58: Line 60:
# <code>GEM</code> → <code>m.i.b.</code> → <code>patch_unit_aio</code> → <code>PATCH NOW</code>
# <code>GEM</code> → <code>m.i.b.</code> → <code>patch_unit_aio</code> → <code>PATCH NOW</code>
# wait fot the patch to be applied
# wait fot the patch to be applied
# after patch is done and unit is rebooted, go to [[REM]] and check if new license keys/FECs are installed and valid.
# after patch is done and unit is rebooted, go to <code>REM</code> and check if new license keys/FECs are installed and valid.


== Install options ==
== Install options ==


=== EU Maps ===
=== EU Maps ===
# GEM → m.i.b. → navigation → check coding → SDS region → Europe → Save changes
# <code>GEM</code> → <code>m.i.b.</code> → <code>navigation</code> → <code>check coding</code> → <code>SDS region</code> → <code>Europe</code> → <code>Save changes</code>
# VCDS/OBD11/VPC → module: 5F → Basic Settings → Formatting Partitions of Internal Memory → Navigation Data Base → Go
# VCDS/OBD11/VPC → module: <code>0x5F</code> → <code>Basic Settings</code> → <code>Formatting Partitions of Internal Memory</code> → <code>Navigation Data Base</code> → <code>Go</code>
# insert SD with MHI2 EU maps
# insert SD with MHI2 EU maps
# System Care → System Update → SD1 → Start Software Update; wait...
# <code>System Care</code> → <code>System Update</code> → <code>SD1</code> → <code>Start Software Update</code>
# wait...


=== Speedtrap PPOIs ===
=== Speedtrap PPOIs ===
# insert SD with PPOIs
# insert SD with PPOIs
# System Care → System Update → SD1 → Start Software Update; wait...
# <code>System Care</code> → <code>System Update</code> → <code>SD1</code> → <code>Start Software Update</code>
# wait...


=== Gracenote ===
=== Gracenote ===


# insert SD with Gracenote update
# insert SD with Gracenote update
# System Care → System Update → SD1 → Start Software Update; wait...
# <code>System Care</code> → <code>System Update</code> → <code>SD1</code> → <code>Start Software Update</code>
# wait...


=== Radiostation Database ===
=== Radiostation Database ===
==== VW / Seat / Skoda ====
# download RSDB update from https://www.phonostar.de
# insert SD with RSDB update
# <code>System Care</code> → <code>System Update</code> → <code>SD1</code> → <code>Start Software Update</code>
# wait...


# insert SD with RSDB update
==== Audi ====
# System Care → System Update → SD1 → Start Software Update; wait...
# download MH2P RSDB
# extract the package, find the <code>VW_STL_DB.sqlite</code> file
# copy it to More Incredible Bash SD card, to <code>/mod/RSDB/</code> directory
# <code>GEM</code> → <code>m.i.b.</code> → <code>multimedia_system</code> → <code>radio</code> → <code>radiostation_db</code> → <code>Copy RSDB to unit</code>
# wait...
 
If you use the VW/Seat/Skoda update, it will result in small logos with a thick border around them. This is due different resolution of the textures (160x120 vs 320x240).


=== Boardbook ===
=== Boardbook ===


Audi and Porsche
Audi and Porsche only


# insert SD with Boardbook
Check <code>0x5F</code> → <code>Long Coding</code>, if the boardbook is enabled
# Settings → Boardbook → install; wait...
 
# insert SD with Boardbook installation package
# <code>Settings</code> → <code>Boardbook</code> → <code>install</code>
# wait...


== Finishing Touches ==
== Finishing Touches ==


=== Video In Motion ===
=== Video In Motion ===
# <code>GEM</code> → <code>m.i.b.</code> → <code>VIM</code> → <code>set VIM to 199km/h</code>
# wait...
=== DVD Region ===
TODOOO
=== Fullscreen RVC mod ===
Audi only
  TODOOO
  TODOOO


=== Fix B201A SVM fault ===
=== Fix B201A SVM fault ===
# VCDS/OBD11/VPC → module: 5F → fix B201A fault with "i'm so XORy" calculator
# VCDS/OBD11/VPC → module: <code>0x5F</code> → fix B201A fault with "i'm so XORy" calculator
 
or
 
# <code>GEM</code> → <code>m.i.b.</code> → <code>SVM_fix</code>


or
or


# GEM → m.i.b. → SVM_fix
# CarScanner ELM OBD2 → TODOOO


== References ==
== References ==

Latest revision as of 09:49, 17 June 2026

A step-by-step tutorial for Harman MHI2 region conversion between US/JP/KR/CN and European firmware.

Prepare the unit, vehicle, and yourself

  1. Check your currently installed firmware. You you have a very old version, your unit might need firmware update first in order to have More Incredible Bash working. And you need it for this to work.
  2. Make sure that power is stable:
    • if working on bench, make sure that the 12V power supply can provide needed amperage
    • if working in vehicle, make sure that the car is connected to external power source or the engine is running. Vehicle equipped with keyless system should have the fob close the the keyless antenna during the procedure.
  3. Make sure that you know those:
    • REM - Red Engineering Menu
    • GEM - Green Engineering Menu
    • SWDL - SoftWare Download
    • FEC - Feature Enabling Code
    • SWaP - SoftWare as a Product

Tools and software

Convert MHI2 unit to European Firmware

Install More Incredible Bash

  1. Insert SD card with More Incredible Bash
  2. REM → Update → SD card → install More Incredible Bash

Prepare unit for EU firmware

  1. GEM → m.i.b. → advanced_settings → eu_conversion → convert unit to EU. It will end with "reboot (..) and run conversion again"
  2. reboot the unit, and run the convert unit to EU again.
  3. ...and again - you see "Now you can insert (...) and update".

Prepare update package for custom full SWLD

  1. GEM → m.i.b. → advanced_settings → swdl_fw_updates → Enable user defined SWDL → ENABLED
  2. GEM → m.i.b. → advanced_settings → swdl_fw_updates → Ignore Region and Variant → ENABLED
  3. exit GEM by going to RADIO. Don't reboot the unit.
  4. insert FAT32 SD with target firmware
  5. REM → Update → User defined → RightButton → Set all to [Y]
  6. if you have premium sound system with external audio amplifier (Bose, Dynaudio, Fender, Bang&Olufsen...), set the amplifier (AMP16*APN / AMP_BAO_P3 / Bose6416*) to [N], because we don't want to update the amplifier. You could do it, but you will need to upload correct parameters to the amplifier afterwards.
  7. if you have Audi A3 8V (AU37x), set the FC2H37xE to [N].[1] This is the display mechanism firmware. If you flash it with the EU firmware version, the mechanism will stay permanently open.

Start the EU firmware update

  1. scroll down → Start update
  2. wait...
  3. In "Device summary" scroll down → Resume
  4. wait for reboot
  5. go to MMI settings and set your language

Patch the unit

Now let's handle FEC / SWaP codes and Component Protection.

  1. GEM → m.i.b. → patch_unit_aio → PATCH NOW
  2. wait fot the patch to be applied
  3. after patch is done and unit is rebooted, go to REM and check if new license keys/FECs are installed and valid.

Install options

EU Maps

  1. GEM → m.i.b. → navigation → check coding → SDS region → Europe → Save changes
  2. VCDS/OBD11/VPC → module: 0x5F → Basic Settings → Formatting Partitions of Internal Memory → Navigation Data Base → Go
  3. insert SD with MHI2 EU maps
  4. System Care → System Update → SD1 → Start Software Update
  5. wait...

Speedtrap PPOIs

  1. insert SD with PPOIs
  2. System Care → System Update → SD1 → Start Software Update
  3. wait...

Gracenote

  1. insert SD with Gracenote update
  2. System Care → System Update → SD1 → Start Software Update
  3. wait...

Radiostation Database

VW / Seat / Skoda

  1. download RSDB update from https://www.phonostar.de
  2. insert SD with RSDB update
  3. System Care → System Update → SD1 → Start Software Update
  4. wait...

Audi

  1. download MH2P RSDB
  2. extract the package, find the VW_STL_DB.sqlite file
  3. copy it to More Incredible Bash SD card, to /mod/RSDB/ directory
  4. GEM → m.i.b. → multimedia_system → radio → radiostation_db → Copy RSDB to unit
  5. wait...

If you use the VW/Seat/Skoda update, it will result in small logos with a thick border around them. This is due different resolution of the textures (160x120 vs 320x240).

Boardbook

Audi and Porsche only

Check 0x5F → Long Coding, if the boardbook is enabled

  1. insert SD with Boardbook installation package
  2. Settings → Boardbook → install
  3. wait...

Finishing Touches

Video In Motion

  1. GEM → m.i.b. → VIM → set VIM to 199km/h
  2. wait...

DVD Region

TODOOO

Fullscreen RVC mod

Audi only 

TODOOO

Fix B201A SVM fault

  1. VCDS/OBD11/VPC → module: 0x5F → fix B201A fault with "i'm so XORy" calculator

or

  1. GEM → m.i.b. → SVM_fix

or

  1. CarScanner ELM OBD2 → TODOOO

References

  1. ↑ https://www.drive2.ru/b/651027432949678987/
Retrieved from "https://wiki.mib-helper.com/index.php?title=MHI2_full_conversion_to_EU&oldid=443"